Worldwide shipping · SS 304 / 316 / 202

Stainless Steel Fasteners for Pune Machine Builders and OEMs

CNC machining of stainless steel threaded parts

Short answer: Pune engineering buyers get the best results when they send a clear drawing with grade, thread, tolerance and finish, and agree on a repeat-supply routine early. Ayr SS makes stainless fasteners to drawing or sample in SS 304, SS 316 and SS 202, and confirms price and lead time in every quotation.

What do Pune OEM buyers need from a fastener supplier?

Machine builders, auto-component suppliers and special-purpose machine makers around Pune work to drawings and audit trails. A fastener that is almost right is a problem on an assembly line. The supplier must therefore be able to read a drawing, ask the right questions, and produce the same part again next quarter.

How do I send a drawing-based enquiry?

Follow these steps so the first quotation is accurate.

  1. Attach the drawing or a clear sketch with dimensions. If you have a sample, say so and we can work from it.
  2. State the grade: SS 304, SS 316 or SS 202, with the property class where strength is critical (ISO 3506).
  3. Give the thread: metric or inch series, pitch and tolerance class.
  4. Name the head or drive type: hex, socket head, countersunk, flange, slotted or special.
  5. Mention finish and marking if the part is cosmetic or visible.
  6. Give annual or per-release quantity so we can plan the route.

This is part of our custom fasteners service.

Which forging route will my part take?

Route affects strength, consistency and economy. Small sizes are generally cold forged, which gives a good grain flow and repeatable dimensions at volume. Large sizes are hot forged. Our listed bolts run to M24 and our studs to M36 in 1000 mm lengths, with larger sizes and other lengths made to order. Tell us the size range of your assembly and we will explain which route applies.

ItemTypical routeCommon standard
Small hex bolts and screwsCold forgedDIN 933, DIN 912
Large-diameter boltsHot forgedDIN 931, DIN 933
NutsCold or hot forged by sizeDIN 934, DIN 985 on request
WashersStampedDIN 125
StudsMachined or rolled threadPer drawing

Nylon-insert and other special nuts depend on the item, so ask if you need one not listed above.

How do I set up repeat supply?

Once a drawing is approved, keep a single part number and revision with us, so each repeat order starts from the same record. Useful habits:

  • Share your forecast, even if it is approximate, so planning can begin before the formal order.
  • Confirm the revision on every release.
  • Ask for a material test certificate at each order if your customer audits traceability.
  • Review the first batch carefully and send us the feedback in writing.

Our quality page describes how we inspect parts, and our services page lists what else we can do. Local details are on the Pune page.

When should I choose stainless over zinc-plated steel?

Choose stainless where corrosion, washdown, food contact, hygiene, or appearance matters, or where plating wear would cause contamination. Stainless fasteners cost more per piece than plated carbon steel, so use them where the application justifies it. Remember that standard austenitic stainless is not hardened like high-tensile alloy steel, so check the load against the property class. For common items, see SS hex bolts and SS hex nuts.

What causes rejections on drawing-based fasteners?

Most rejections trace back to an incomplete specification rather than a manufacturing fault. Typical gaps are an undefined thread tolerance, no stated length tolerance, an unclear head height, a missing property class, or a drawing that shows a part but not the grade. When two readings of a drawing are possible, one of them will usually be the one that does not fit on your line.

Before releasing a new part, read the drawing as if you were seeing it for the first time and ask what a supplier would have to guess. Fill in those gaps, and mention critical dimensions that need checking with a gauge. If you are unsure, send it anyway and we will point out what is unclear before work begins. That conversation costs minutes, while a wrong first batch costs the assembly schedule.

Frequently asked questions

Can you match a sample if I have no drawing?

Yes. Send the sample and the application. We measure it, confirm the likely grade and thread, and quote against that.

Do you work in both metric and inch sizes?

Yes, both series are available, so imported machinery spares are covered as well.

Can you supply the same part repeatedly?

Yes. Keep the part number and revision stable and we will quote and plan each release against the same specification.

Ready to move ahead? Send your drawing, sample or size list and request a quote. You can also call +91 89196 74214 or write to ayrssnutbolt@gmail.com, and our team will reply with price and lead time in the quotation.

Need stainless steel fasteners like these?

Send your grade, size, quantity and standard. We reply with a quotation and confirm availability, standards and documents before you order.

Share this article

Keep Reading

Related Articles