Worldwide shipping · SS 304 / 316 / 202

Metric Thread Pitch Chart: Coarse and Fine, M3 to M24

Stainless steel studs and threaded rods

Short answer: Metric coarse pitches run from 0.5 mm on M3 to 3 mm on M24, and if you give only a size such as M10, the coarse pitch of 1.5 mm is assumed. Fine pitches such as M10x1.25 must be written out on the order. The full chart is below.

What is the coarse pitch for each metric size from M3 to M24?

Pitch is the distance in millimetres between neighbouring thread crests. A coarse thread is the default for a standard metric bolt or nut, which is why the pitch is not usually written in the size.

SizeCoarse pitch (mm)
M30.5
M40.7
M50.8
M61
M81.25
M101.5
M121.75
M162
M202.5
M243

You can see how these sizes sit within the standards we supply on our standards page.

When you read a thread callout, the first number is the nominal diameter and the second is the pitch, both in millimetres. So M12x1.5 means a 12 mm thread with 1.5 mm between crests, while plain M12 means the 1.75 mm coarse pitch. Mixing these up is easy to do on a long order list, so write the pitch out in full.

Which fine pitches are commonly used?

A fine thread has a smaller pitch for the same diameter. The fine pitches that buyers ask for most often in this size range include:

  • M8x1
  • M10x1.25
  • M12x1.25 and M12x1.5
  • M16x1.5
  • M20x1.5
  • M24x2

Fine threads have a shallower thread depth, a slightly larger stress area for the same diameter, and finer adjustment, which is why they are used in some machinery, automotive and instrument work. Coarse threads, in contrast, are quicker to assemble, more tolerant of dirt and minor damage, and usually easier to source. For general use, coarse is the sensible default.

Fine pitch is also what you will meet where a thread is cut into a thin wall, where a very small adjustment is needed, or where vibration is a concern and the lower helix angle helps hold the preload. In ordinary structural and general engineering work, stay with the coarse series unless the drawing says otherwise.

How do I specify a thread on a purchase order?

A clear thread description removes the most common cause of wrong shipments. Write it in this order:

  1. Diameter and pitch: “M12” for coarse, “M12x1.5” for a fine pitch. When it is a fine pitch, add the word “fine” so it cannot be missed.
  2. Length: for a bolt, the length under the head, for example M12x1.5×60.
  3. Standard: DIN, ISO or BS, with the number.
  4. Grade: SS 304, SS 316 or SS 202.
  5. Thread tolerance, if needed: such as 6g for bolts or 6H for nuts. If you leave it out, the standard’s default applies.

If you are matching an existing part, send us the old fastener or a thread gauge reading. A pitch gauge or a calliper measuring across a few threads is enough to identify the pitch. Fastener lists for common bolt types are on our SS hex bolts page, and the full range is on the products page.

Does thread pitch affect stainless steel galling?

Galling, also called cold welding or seizing, is a known problem when stainless steel threads slide against each other under load, especially at speed, and it is common in austenitic grades. Pitch does not cause it by itself, but a few points are worth knowing:

  • Tighten slowly. Fast tightening with power tools generates heat and friction and raises the risk.
  • Use a suitable anti-seize or lubricant compatible with your application.
  • Keep threads clean, since grit and chips can start a seizure.
  • Avoid damaged threads, and keep nut and bolt threads in good condition.
  • Where the design allows, use a coarse thread rather than a fine one, because coarse threads are more tolerant of minor damage.

For help with grade choice and thread selection on difficult assemblies, see our services and the grade notes on SS 304 fasteners.

Stainless nuts and bolts are also more likely to seize when the thread fit is tight, so ask for the thread tolerance class that matches your assembly method, and tell us if the part will be tightened with power tools.

Frequently asked questions

What is the pitch of an M10 bolt?

The coarse pitch is 1.5 mm. Fine pitches of 1.25 mm and 1 mm also exist, but you must specify them.

Can I use a fine-pitch nut on a coarse-pitch bolt?

No. The thread pitch must match. An M10x1.25 nut will not fit an M10 coarse bolt, and forcing it will damage both parts.

How do I measure the pitch of a bolt?

Use a thread pitch gauge, or measure the distance across ten threads with a calliper and divide by ten. Compare the result with the chart above.

Can you make special or non-standard threads?

Yes. We make bolts, nuts, studs and screws to drawing, so send us your drawing or sample with the pitch and tolerance you need.

Ready with your thread list? Request a quote, or call +91 89196 74214, or write to ayrssnutbolt@gmail.com.

Need stainless steel fasteners like these?

Send your grade, size, quantity and standard. We reply with a quotation and confirm availability, standards and documents before you order.

Share this article

Keep Reading

Related Articles