Short answer: A flange nut is a hex nut with a built-in washer face, so it spreads the clamp load over a wider area in one part. A hex nut with a separate washer does the same job but gives you more freedom over washer size, material and type. Use flange nuts for faster assembly and neat, repeatable joints, and hex nuts with a washer when you need a larger or special washer.
What is the difference between a flange nut and a hex nut?
A hex nut is a plain six-sided nut that bears on the surface only through its own small face. A flange nut has a wide circular collar at the base, formed in one piece with the nut, which acts as an integral washer. A flange nut is usually tightened with the same spanner size as a hex nut of the same thread.
We list SS 304 flange nuts from M4 to M12. For plain nuts, our stainless steel hex nuts run from M2 to M36 in SS 304 and SS 316. See the flange nut range on our stainless steel flange nuts page.
How does each one spread the load?
The wider bearing area of a flange nut reduces the pressure on the part being clamped. That helps on thin sheet metal, plastic, aluminium and painted surfaces, where a small hex face could dig in or deform the panel. A hex nut with a flat washer achieves the same result, and the washer can be bigger than the integral flange, so a large-diameter washer is the better choice for very soft or thin material or for oversized and slotted holes.
What about vibration?
A plain flange nut has no locking feature, so it is no more vibration-proof than a hex nut with a washer. Some flange nuts have a serrated underside that bites into the surface to resist turning, but serrations can mark or damage the surface and they are less suited to stainless-on-stainless or finished surfaces. If vibration is a concern, use a proper locking solution, such as a nylon-insert lock nut (see our nylock nuts) or a thin lock nut used as a jam nut, or add a spring washer, and check the joint after a period of service.
When should I choose a flange nut?
- Production assembly: one part instead of two means fewer items to handle and no washer left out by mistake.
- Space-limited joints: a flange nut stacks lower than a nut plus washer.
- Thin or soft material: the larger bearing area lowers surface pressure.
- Neat appearance: equipment, frames and enclosures benefit from the clean look.
When is a hex nut with a washer better?
- Large or slotted holes: you can pick a washer that covers the opening.
- Very soft materials: a wide plate or fender washer spreads the load further.
- Sizes outside the flange range: hex nuts cover M2 to M36 against flange M4 to M12.
- Mixed materials: a nylon or other washer can isolate dissimilar metals.
- Needing a specific grade: hex nuts are available in SS 316 as well as SS 304.
Whichever you choose, match the nut to the bolt grade. Our hex bolts are available in SS 304 and SS 316, and our guide to preventing galling explains how to tighten stainless threads without seizing them.
How do I decide for my own assembly?
Ask three questions. First, how soft or thin is the clamped material? If it is thin sheet, plastic or a painted panel, a flange nut or a wide washer is worth using. Second, how many joints are you assembling? If it is a large number, the single-part flange nut saves handling time and avoids missing washers. Third, what size and grade do you need? Flange nuts in our list stop at M12 in SS 304, while hex nuts run from M2 to M36 and also come in SS 316, so larger sizes or marine duty will lead you to a hex nut with a washer. Write the choice on the drawing so the same part is bought every time, and tell us the bolt size and the clamped material when you enquire.
Frequently asked questions
Is a flange nut stronger than a hex nut?
The thread strength is set by the nut grade and height, not by the flange. The flange mainly improves the bearing area under the nut.
Can I use a flange nut with a washer as well?
You can, for example over an oversized hole, but in most cases the integral flange makes an extra washer unnecessary.
Do flange nuts need a different spanner?
No. They are tightened on the hexagon, so use the same spanner you would use for the equivalent hex nut.
Do you supply flange nuts in SS 316?
Our listed flange nuts are SS 304. If you need another grade, ask through an enquiry and we will respond.
Ready to specify? Send your sizes, grade and quantity through the request a quote page, call +91 89196 74214 or email ayrssnutbolt@gmail.com and our team will respond with a quotation.



