Short answer: A DIN 912 M8 socket head cap screw has a 13 mm head diameter, 8 mm head height and takes a 6 mm hex key. The chart below covers M3 to M24. Choose a cap screw over a hex bolt when you need a compact head, a counterbored fit or tight spaces. Verify dimensions against the current standard.
What are the DIN 912 allen cap screw dimensions?
DIN 912 describes the cylindrical head socket cap screw, driven with a hex key (Allen key). All values below are in millimetres.
| Thread size | Head dia. (mm) | Head height (mm) | Hex key (mm) |
|---|---|---|---|
| M3 | 5.5 | 3 | 2.5 |
| M4 | 7 | 4 | 3 |
| M5 | 8.5 | 5 | 4 |
| M6 | 10 | 6 | 5 |
| M8 | 13 | 8 | 6 |
| M10 | 16 | 10 | 8 |
| M12 | 18 | 12 | 10 |
| M16 | 24 | 16 | 14 |
| M20 | 30 | 20 | 17 |
| M24 | 36 | 24 | 19 |
Notice that the head height equals the thread diameter, which is the easy way to remember it. Treat the table as a quick reference and confirm against the current edition of the standard, as described on our DIN 912 page.
What property classes are available in stainless steel?
Stainless fasteners are classed under ISO 3506, using a letter for the steel family and a number for strength. Common examples are A2-70 and A4-70, where A2 is the family that includes SS 304 and A4 is the family that includes SS 316, and 70 indicates the strength level. A2-80 and A4-80 are higher-strength options. Check what is marked on your drawing and tell us when ordering. You can read more about the grades on our SS 304 and SS 316 pages.
When should I choose a cap screw over a hex bolt?
- Limited space: the round head with internal drive needs less room around it than a spanner or socket on a hex head.
- Counterbored holes: the head can sit below the surface for a flush, tidy finish.
- Machine and tooling assemblies: cap screws are common where parts are bolted into tapped holes with a clean look and good clamping.
- Appearance and safety: no sharp hex corners to snag.
Choose a hex bolt when you want easy fastening with ordinary spanners, a wider bearing area under the head, or a lower cost standard part for general structural use. A hex bolt is also easier to tighten in the field without a set of keys.
What should I check before ordering?
- Thread size and pitch, and length measured under the head.
- Grade (SS 304 or SS 316) and property class.
- Whether you need a plain finish or something special.
- Matching nuts, washers or tapped holes.
We supply stainless allen cap screws in metric and inch series, and you can explore the complete range for matching parts.
How do I pick the right length and key?
Length on a DIN 912 screw is measured from under the head to the tip, since the head sits inside or on top of the part. Add the thickness of the material being clamped, any washer, and the thread engagement you need in the tapped hole, which is commonly at least one thread diameter in steel. For stainless screws into stainless threads, take extra care with tightening, as stainless can seize (gall) when driven dry. A light lubricant or anti-seize compound and a steady, not fast, tightening speed help prevent this.
For the key, use the size in the chart and make sure the tool is in good condition. A worn key rounds the socket, especially on small sizes like M3 and M4. Keep one good key per size, and replace worn ones before they damage screws. If you are working in tight spaces, a ball-end key helps, but use a straight key for the final tightening to get full contact in the socket.
Before placing an order, also confirm that your counterbore is deep and wide enough for the head diameter and height in the chart, with a little clearance. A head that does not fit the counterbore is a common and avoidable drawing error, and checking it early costs nothing.
Frequently asked questions
What size Allen key fits an M10 cap screw?
An 8 mm hex key fits an M10 DIN 912 screw, according to the chart above.
Is DIN 912 the same as a socket head cap screw?
Yes, DIN 912 is the German standard for the cylindrical head hex socket cap screw, which is commonly called an allen cap screw or socket head cap screw.
Can you supply custom lengths?
Yes. Lengths and special requirements can be made to order. Send your drawing or sample and we will advise.
Ready to move forward? Send us your details and request a quote, or call +91 89196 74214 or email ayrssnutbolt@gmail.com.



