Short answer: DIN 982 is the tall nylock nut and DIN 985 is the thin one. Choose DIN 982 when you have room for the extra height and want more thread engagement and a deeper nylon ring; choose DIN 985 where space is tight. Both resist loosening from vibration through the nylon insert, but neither suits high temperatures or many repeated tightenings.
What is the difference between DIN 982 and DIN 985 nylock nuts?
Both are hexagon nuts with a nylon ring pressed into a collar at the top. As the bolt threads cut into that ring, the nylon grips the thread and creates a prevailing torque, so the nut resists backing off under vibration. The difference is height.
- DIN 982 (tall or high type): the nut body plus the nylon collar gives more total height, more threads engaged and a deeper insert.
- DIN 985 (thin or low type): a shorter nut with the same insert principle, made for assemblies where there is little projecting thread or little clearance.
We list DIN 982 in sizes M3 to M30 and DIN 985 in sizes M6 to M16, both in SS 304 and SS 316. Browse the full range on our stainless steel nylock nuts page.
When should I choose the tall DIN 982 nut?
Pick the tall nut when the joint carries vibration and there is enough bolt length and clearance. The extra height gives the thread more grip and the longer insert holds its prevailing torque better over time. It is the usual choice for machinery guards, motor mounts, pumps, conveyor frames and equipment that is shaken or shocked in service.
It also makes sense when the bolt will stand proud of the nut. A taller nut gives you a clear margin to confirm that at least one full thread is visible beyond the nylon, which is a common inspection check.
When is the thin DIN 985 nut the better fit?
Choose the thin nut where space or weight limits you: sheet metal enclosures, electrical panels, thin brackets and tight clearances around moving parts. It still gives a locking action, though with less thread engagement than the tall form. For a load-bearing structural joint, check the bolt strength and thread engagement your design needs before you drop to the thin type.
If a standard plain nut will do, our stainless steel hex nuts are the simpler option; use nylock only where you want the added vibration resistance.
What are the limits of the nylon insert?
The metal body of a stainless nut tolerates heat far better than the polymer ring does. Keep these limits in mind.
- Temperature: nylon softens and loses grip as it gets hot. As a conservative rule, treat nylock nuts as suitable for moderate temperatures only, commonly quoted as up to about 100 to 120 degrees Celsius, and confirm the figure for your application. For exhausts, furnaces, boilers and similar zones, use an all-metal lock nut instead.
- Reuse: each time the nut is run on and off, the thread leaves a deeper groove in the insert and the locking torque falls. Use new nuts for critical joints and after any dismantling. A nut that spins freely by hand all the way on has lost its lock and should be replaced.
- Chemicals: some solvents, fuels and strong chemicals attack nylon. Check compatibility for your environment.
Does stainless steel galling affect nylock nuts?
Yes. The nylon insert does not remove the risk of galling between the stainless nut thread and a stainless bolt, because the metal threads still slide against each other under load. Tighten slowly rather than with a fast impact driver, keep threads clean, and use a suitable lubricant or anti-seize compound where the application allows. Our guide on how to prevent galling in stainless steel fasteners covers this in detail. Note that lubricant also changes the torque-to-clamp relationship, so reduce the tightening torque accordingly.
Which grade should I order, SS 304 or SS 316?
SS 304 (A2-70) suits general indoor, outdoor and food-handling use. SS 316 (A4-70) contains molybdenum and handles chlorides, marine air, coastal sites and many chemical environments better. See our pages on SS 304 fasteners and SS 316 fasteners, or read SS 304 vs SS 316 fasteners to decide. Match the nut grade to the bolt grade; see our hex bolts for mating sizes.
Frequently asked questions
Can I use a nylock nut on a hot exhaust or furnace part?
No. The nylon insert will soften at high temperatures and the nut will lose its locking action. Use an all-metal lock nut for hot zones.
How many times can a nylock nut be reused?
There is no safe fixed number. The lock weakens with every cycle, so use a fresh nut for critical or vibration-loaded joints and replace any nut that no longer offers resistance when turned.
Is DIN 985 as strong as DIN 982?
Both are made to the same material properties, but the thin nut has fewer threads engaged, so the tall nut is the safer choice where the joint is heavily loaded.
Do you supply both standards in both grades?
Yes, in the size ranges listed above in SS 304 and SS 316. For standards and documentation questions, see our standards page.
Ready to specify? Send your sizes, grade and quantity through the request a quote page, call +91 89196 74214 or email ayrssnutbolt@gmail.com and our team will respond with a quotation.



